Topic: cd rom problems...

[cute_boyz]

mga bossing help nmn....
need ur advice bout my cd-rom n Asus 52x....
bumili kc ko nun e ayaw gumana,,,
pag kinakabit ko...ayaw mag boot....
"DISK BOOT FAILURE" ang nakasulat tapos di ma detect ung HD ko....
pag tiningnan ko sa bios,,,none ang HD ko....
sinubukan ko ng pag palit2in ang mga wires pero buo namn ang wires...
sinubukan ko n ding ung power pero ok nmn....
mga bossing...
give me some tips....
ur comments will greatly be appreciated...tanx...

[NecroRise]

jumper settings bro.. baka pareho master.........

[realwired73]

Kapag hindi guman yun suggestion ni Kashin. Baka sira yan nabili mo, I suggest that you have it change na lang. Basta i-check mo yun settings mo, punta ka ng CMOS din.

[jprizal]

check mo jumper settings bro...'tsaka kung naka-auto detect ang hdd detection sa bios mo...

[yonipspy]

check jumper settings set to secondary master or slave... depende sayo... or try to change another ide cable baka hindi compatible sa cdrom mo... sabi mo ma detech sya sa bios meaning oks yan... check mo lang sa mga cable connection mo baka dyan lang ang problem...

[cute_boyz]

bro,,,
gumagana sa ibang pc...
try ko ung cmos...
nka auto detect nga pala hd ko...
hanap ko ung snsbi nyong settings


tanx bro...

[wolfpaq]

May isang technique na maaring makakasolve ng problema mo. While on BIOS mode, lit the three LED on your keyboard by pressing Numlock, CapsLock at Scroll Lock. Then highlight Load Default Configuration and hit ENTER. Save and Exit...


Subukan mo yan laging effective yan when it comes to hardware problems.

Dont forget the pokepoint natin jan pag tama ha....

[cute_boyz]

bossing...
pag sinasaksak ko ung cd rom,,
di ko n ma detect hd ko???

dun sa ibang bro,,,
di ko mahanapung jumper settings...

tanx...

[lyer]

bossing...
pag sinasaksak ko ung cd rom,,
di ko n ma detect hd ko???

dun sa ibang bro,,,
di ko mahanapung jumper settings...

tanx...

try to use two IDE cable.....then set ur drive in cmos in "auto detect".....put ur hard disk in primary master and secondary master for cd rom..........

[puretuts]

sa mga computers you can only put one master in one ide cable. Ergo if you are using your ide cable with 2 master (ex. 1 hd as a master and 1 cd as master) one will not be recognized. Dapat one master one slave. Check your jumper setting. Naka lagay din sa likod ang placement of the jumper. or you can use another separete id cable.


good luck.

[cute_boyz]

sa mga computers you can only put one master in one ide cable. Ergo if you are using your ide cable with 2 master (ex. 1 hd as a master and 1 cd as master) one will not be recognized. Dapat one master one slave. Check your jumper setting. Naka lagay din sa likod ang placement of the jumper. or you can use another separete id cable.


good luck.

bossing...
dati 1 csble lng gamit ko..
bale,,my cd rom un dati nasira lang...
so pinaltan ko ng iba pero ayaw na gumana..
about the settings..
i've tried many times on editing the cmos but still it doesnt work..
it doesn't even recognize the hdd....
but its on AUTO-DETECT....
any more idea???

May isang technique na maaring makakasolve ng problema mo. While on BIOS mode, lit the three LED on your keyboard by pressing Numlock, CapsLock at Scroll Lock. Then highlight Load Default Configuration and hit ENTER. Save and Exit...


Subukan mo yan laging effective yan when it comes to hardware problems.

Dont forget the pokepoint natin jan pag tama ha....

about ur opinion sir...
ill try it ater.tanx...

[TobleRONe]

bro sa mga nabasa ko, di mo makita jumper settings. gumamit ka na lang ng isa pang IDE cable para sa cd rom mo. yung HDD leave it as it is. gamitan mo na ng isa pang cable iyang CD rom at saka mo ilagay sa secondary. chances are pareho nga nakamaster ang settings.

BTW, saan mo hinahanap yung jumper setting?

[oponco]

check mo CMOS settings mo, tapos check mo baka naka master yan. change mo to slave or secondary